Your Complete Plumbing Guide for Installing a Bathtub
Your Complete Plumbing Guide for Installing a Bathtub
Blog Article
We've found the article relating to Tools You Need to Install a New Bathtub directly below on the internet and believe it made perfect sense to share it with you on this site.

Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is conveniently easily accessible, the project can relocate easily; if you have to open up a wall to remove the old tub as well as place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and also set in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is better to think about employing one before you start. Possibilities are you may need a professional plumber to make tube connections.
This post will assist you mount a brand-new bath tub in your bathroom if you have currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water supply pipelines.
Your devices as well as material list need to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome because of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the taps have been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Secure the tap in position with the maker provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bathtub up until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the same for the other faucet.
Activate the supply of water as well as check all joints and brand-new pipework for leakages and tighten them if necessary. Load the bath tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling and also sealing around the tub ought to wait till the bathtub has actually been used at least when as this will certainly resolve it into its last setting.
Planning for the Installment
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, bring about issues with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can break relatively early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We were shown that write-up about Tools You Need to Install a New Bathtub through an associate on our other domain. Kindly take a moment to promote this content if you enjoyed it. I am grateful for your time. Don't hesitate to pay a visit to our website back soon.
Schedule Today Report this page